How could a machine run with a disturbing power source? However, today we are talking about the Stihl chainsaw and its power source, of course, the oiler adjustment!
You know, lubrication is vital to the Stihl chainsaw; for its all-over functions and performs. So, running it with a sick oiler isn’t fair, Right? But how to adjust oiler on Stihl chainsaw?
All you need to do is check the oiler in different ways, fix the problems it faces, clean sawdust, adjust the screw, and replace the pump if needed.
Don’t you think it’s crucial to get these tricks elaborately? We think so!
How Do You Adjust The Stihl Chainsaw Oiler?
Sometimes it happens; you may have lubricated the oil pump enough to get the power to slice very hard surfaces, but the oiler isn’t working at all.
No worries, as it’s a common circumstance with any chainsaw, several ways are there to fix it as well. At first, you should check the oiler adjustment, then fix it and replace the oil pump if needed.
Let’s get it elaborately, shall we?
How Do You Know If Your Chainsaw Oiler Is Working?
Some classic ways are here for you to check your saw’s oiler if it’s working or not.
The Chain Should Be Oily In Touch.
At first, you should start up the chain saw for a while with the chain spinning. Just run it for a bit; no need to cut through wood!
Then take a close look at the chain or touch it; it should be oily. Also, lift the chain from the drive links and check if there is a bit of oil on them.
However, if the chain has an oily film on it, you shouldn’t be worried. The Stihl chainsaw is getting oil enough.
Running Chain Would Spray Oil On Objects.
This trick also needs the running chainsaw without cutting through wood.
You need cardboard, paper, or things like that where the spray of oil can be seen properly. However, take any and hold the chainsaw one or two inches away from it.
Pointing the end of the bar to the cardboard, run it. You will see the spray of oil on the cardboard in case your chainsaw has a good lubricant.
Also, to make sure the coming oil is constant, do the same trick for few times.
Oil Should Be Coming Out of The Oiler Hole.
In the third method, you need to take off the clutch cover by removing the nuts on bolts on it. Then take out the chain and bar as well.
Here, you need to check if drops of oil are coming from the oiler hole or not.
Run the chainsaw but don’t rev it too high. Remember, when you have the chain saw without other parts and chain installed, you have to be extremely careful to run it as there is a chance the clutch could come off the saw.
However, while you start up the chain, drops of oil should be coming out from the oiler hole. If it’s okay, then be sure your chainsaw is oiling properly.
In case all is okay, but you’re still not getting oil to the chain, check the oiler hole and inside of the bar. Make sure these are not plugged with sawdust.
If all are clear and open, replace the bar and chain and check it!
How To Adjust Oiler On Stihl Chainsaw? 3 Easy Steps
Here are some tips and solutions to problems you would face while checking or adjusting the Stihl chainsaw oiler.
Step 1 – Take Precautions
Before removing the nuts, you should turn off the chainsaw and let it cool. Wear leather gloves to protect your hands from oil and chain.
You need an adjustable wrench to remove the nuts.
Use a small flat-head screwdriver to clean up any sawdust on the oil inlet hole and bottom of the bar. Also, clean the oil way on the motor housing with that.
Step 2 – Remove nuts & clean the oil tank
You need an adjustable wrench to remove the nuts.
Use a small flat-head screwdriver to clean up any sawdust on the oil inlet hole and bottom of the bar. Also, clean the oil way on the motor housing with that.
Step 3 – Turn the bolts clockwise to adjust
If you face a higher or lower amount of oil spray ( in checking method two), use a flathead screwdriver on the oil adjustment screw. Turn it clockwise to reduce the oil feed rate and counterclockwise to decrease it.
Stihl chainsaw has a left-handed locking mechanism. Thus, to loosen the locks and bolts turn these clockwise.
Still Getting No Oil? Replace The Oil Pump
You have checked your Stihl chainsaw using the three methods above and fixed it, but still not getting oil. If it is, you might have to get it professionally checked because, in that case, the problems may lie in the oil pump.
However, you can check and clean the oil pump at home.
- Unscrew the clutch assembly
- Lossen every bolt and lock clockwise
- After getting the oil pump, slide it out to disassemble every part.
- Look for any damages.
- Clean it out properly. You can use gasoline, wire brush, and rag here.
So when to replace the pump? If you notice any broken parts on the oil pump, it’s better to replace the pump with a new kit.
What Happens To A Chainsaw Without Bar Oil?
Do you know why oiling is significant for your saw? Well, in a word, it’s for the safety of your project, your chainsaw saw, and of course yourself.
Indeed, without enough lubrication, your saw would face several safety issues like:
- chain breaking,
- kickback
- bar and chain-wearing
- engine load increasing
- heat soak,
- mostly dulls the chain.
Moreover, to run your project smoothly, you need a handy tool. But when your chainsaw oiler doesn’t have enough oil, it will slow the chain causing friction in the bar and chain. It will then damage your saw or lessen the smoothness you wanted.
Not to mention the chain-breaking facts; you know, it’s a serious safety concern. Running the saw without oil or with a little oil will increase the chance of breaking it.
Indeed, using a chainsaw without oil isn’t less than a dangerous curriculum, is it?
Conclusion
Hopefully, our tricks and tips on how to adjust oiler on Stihl chainsaw were helpful to you. Moreover, the Stihl chainsaw has a simple lubrication adjustment.
Problems you could face with the oiler can be simply fixed; just some awareness and safe tricks are all you need. And you have got these already!
